Sharp IR Sensor Mounting Bracket

BUY NOW

Introduction

This mounting bracket is designed for Sharp distance measuring sensor

Specification

Size:45x20x15mm
Mounting hole distance:14mm
Weight:5g

BUY NOW

Like us on Facebook

News from our store

Lithium Battery Charger

If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The Lithium Battery Charger can charge 3.7V LiPo battery at a rate of 500mA per hour. It is designed to charge single-cell Li-Ion or Li-Polymer batteries. Check the datasheet below to see if it will work with your battery.

3262_0 - 12V/0.9Kg-cm/285RPM 14:1 DC Gear Motor

Product Features
This DC motor has a 14:1 gearbox, a rated speed of 285 RPM and rated torque of 0.9 Kg·cm.

Product Description

The 3262 is a 12 volt gear motor, generating 0.9 Kg-cm of torque at 285 RPM. This motor is quite compact considering the amout of power it can output.

The planetary gearbox on this motor is more sophisticated than a typical spur gearbox and will provide greater efficiency, higher torque, and quieter motor operation.

CAN-BUS Shield

This CAN-BUS Shield is designed specially for Arduino UNO with STM32, to give your Arduino CAN-BUS capability.

Sharp IR Sensor Mounting Bracket

Introduction

This mounting bracket is designed for Sharp distance measuring sensor

Led holder 3 mm (Bag of 3)

Mini Maestro 12-Channel USB Servo Controller (Assembled)

The 12-channel Mini Maestro 12 raises the performance bar for serial servo controllers with features such as a native USB interface and internal scripting control. Whether you want the best servo control available (0.25μs resolution with built-in speed and acceleration control and pulse rates up to 333 Hz) or a general I/O controller (e.g. to interface with a sensor or ESC via your USB port), this compact, versatile device will deliver. This fully-assembled version ships with header pins installed.

CMPS10 - Tilt Compensated Compass Module

The CMPS10 module is a tilt compensated compass. Employing a 3-axis magnetometer and a 3-axis accelerometer and a powerful 16-bit processor, the CMPS10 has been designed to remove the errors caused by

1103_1 - IR Reflective Sensor 10cm

Product Features
This IR proximity sensor can detect opaque objects within 10cm and connects to an analog input.

Product Description

This sensor can detect the presence of objects at a distance of 0 to 10cm regardless of the object reflective properties. When an object enters the range of detection, SensorValue becomes zero, and when it leaves, it returns to 1000. The 1103 works just as well in both dim and well lit environments.

DIGITAL IR Transmitter Module

Introduction

IR Transmitter Module is designed for IR communication when paired with IR receiver module.

Relay Shield

The Relay Shield is an Arduino compatible module that provides an easy way to control high voltage thanks to 4 independent channels equipped with photo-coupled mechanical relays preassembled on the board.

Adafruit Wave Shield for Arduino Kit - v1.1

Adding quality audio to an electronic project is surprisingly difficult. Here is a shield for Arduinos that solves this problem. It can play up to 22KHz, 12bit uncompressed audio files of any length. It's low cost, available

3255_0 - 12V/0.3Kg-cm/127RPM 18:1 DC Gear Motor

Product Features
This DC motor has a 18:1 gearbox, a rated speed of 127 RPM and rated torque of 0.31 Kg·cm.

Product Description

The 3255 is a 12 volt gear motor, generating 0.31 Kg-cm of torque at 127 RPM. It is very efficient for its size, so less power is lost in the form of heat.

3137_0 - Button Load Cell (0-200kg) - CZL204E

Product Features
This load cell measures compressive forces of up to 200kg and connects to a bridge input.

Product Description

A load cell is a force sensing module - a carefully designed metal structure, with small elements called strain gauges mounted in precise locations on the structure. Load cells are designed to measure a specific force, and ignore other forces being applied. The electrical signal output by the load cell is very small and requires specialized amplification. Fortunately, the 1046 PhidgetBridge will perform all the amplification and measurement of the electrical output.

M3 hex nut driver (5,5mm)

1 hex nut driver that is both suited for MakerBeam and OpenBeam products.

Bipolar (BJT) Single Transistor, PNP

TRANSISTOR, PNP, 45V, 0.1A, TO-92
Transistor Polarity: PNP
Collector Emitter Voltage V(br)ceo: 45V

1120_0 - FlexiForce Adapter

Product Features

The FlexiForce adapter allows you to connect one FlexiForce FSR to a Phidgets analog input.

Product Description

The 1120 FlexiForce Adapter makes it easy to interface a Tekscan FlexiForce Force Sensor to your PC. Just use the cable included with the adapter. We even give you a round plastic disc for the sensing pad.

BATTERY CONNECTOR, PP3 TYPE 1,150MM

The 440005P from Multicomp is a snap on connector/strap for use with PP3 battery.

3652_0 - LCD Screen 2x20 - LCM2002J

Product Features
A 2 line by 20 character backlit LCD display. Each character is 5.9x12.7mm.

Product Description

The 3652 is a 2 lines x 20 characters LCD module with a large viewing area of 147 x 35mm. The 6 x 12mm characters are nice and big. From software, the LCD contrast, and the LED backlight brightness can be adjusted.

Input Output Expansion Shield For Arduino
Our IO expansion board is evolving, this latest V5 IO expansion shield is now supporting Xbee. It combines our popular Xbee shield with IO expansion shield(V4). It even supports SD card which provides the ultimate

Pololu Ball Caster with 3/8" Metal Ball

This small ball caster uses a 3/8" diameter metal ball. The height of the assembled kit ranges from 0.4" to 0.6".

CMPS03 - Compass Module
Overview
This compass module has been specifically designed for use in robots as an aid to navigation. The aim was to produce a unique number to represent the direction the robot is facing. The compass uses the Philips KMZ51 magnetic field sensor, which is sensitive enough to detect the Earths magnetic field. The output from two of them mounted at right angles to each other is used to compute the direction of the horizontal component of the Earths magnetic field.

3133_0 - Micro Load Cell (0-5kg) - CZL635

Product Features
This load cell measures shear force up to 5kg and connects to a bridge input.

Product Description

ETH-RLY02 - 16Amp, 2 Channel Relay Module
Overview
The ETH002 provides two volt free contact relay outputs with a current rating of up to 16Amp each. The module is powered from a 12vdc supply which can be regulated or unregulated. The DC input jack is 2.1mm with positive core polarity, DC supplies are required to supply at least 500mA at 12vdc.

BATTERY CONNECTOR, PP3 TYPE 1,150MM

The 440005P from Multicomp is a snap on connector/strap for use with PP3 battery.

IDC2x5 Cable

This cable is especially designed for Interface shield, LED RGB Module. It is has a female 2×5 IDC connector on each end that is designed to plug into a 0.100" (2.54 mm) 2×3 shrouded box header.

m3pi Expansion Kit for 3pi Robot

The m3pi expansion kit contains everything you need to turn your 3pi robot into an enhanced m3pi robot. The expansion PCB ships with all the surface-mount parts populated,

1065_0 - PhidgetMotorControl 1-Motor

Controlla un motore con encoder, ha due ingressi analogici e due ingressi digitali. Si connette alla porta USB.

Bag of 10 M3 nuts

SOCKET IC, DIL, 0.3", 14WAY

The 1-390261-3 from TE Connectivity is a 2.54mm pitch, 14 position ladder style DIP socket.

Mini Pushbutton Switch: PCB-Mount, 2-Pin, SPST, 50mA (5-Pack)

These small, two-pin, momentary tactile buttons are intended for mounting to PCBs, but they can also be plugged into standard 0.1" breadboards.

3264_0 - 12V/8.4Kg-cm/28RPM 139:1 DC Gear Motor

Product Features
This DC motor has a 139:1 gearbox, a rated speed of 28 RPM and rated torque of 8.46 Kg·cm.

Product Description

The 3264 is a 12 volt gear motor, generating 8.46 Kg-cm of torque at 28 RPM. This motor is quite compact considering the amout of power it can output.

The planetary gearbox on this motor is more sophisticated than a typical spur gearbox and will provide greater efficiency, higher torque, and quieter motor operation.

Arduino 2009 Shield - Motor PCB

PCB to mount: it allows to Arduino boards to drive 2 12V DC motors

2wd miniQ Robot chassis

This 2WD miniQ robot is especially designed for education and hobbies. It features a powerful metal gear motors which provide a speedy robot. Ideal for maze competition and education purpose.

Precision screwdrivers slot PG1-4 3x100

L7812CV - IC, V REG +12V, 7812, TO-220-3

This regulator can provide local on-card regulation, eliminating the distribution problems associated with single point regulation.

Micro USB to Serial Adapter

Description

Micro USB to Serial Adapter is a usefull tool that allows to connect Personal Computers with any microcontroller system via the USB port. This tiny and lightweight board is only 19x13 mm, including the mini-B connector, and its weight is only 1,4 gr (0,05 oz). Interfacing is realized by two 0,100” strip connectors that are distant 0,600” (15,24mm); this allows a stable and easy mounting on solderless breadboard and sockets.

UA741CN Operational Amplifier

Amplifier Case Style: DIP
Bandwidth: 1MHz

3109_0 - TPK-01G Bead Probe K-type Thermocouple (-50°C to +450°C)

Product Features
This K-Type thermocouple measures temperatures from -50°C to 450°C and connects to a Phidgets thermocouple board.

Product Description

The 3109 thermocouple can measure temperatures between -50°C to +450°C with a ±0.75°C accuracy.

The thermocouple wire is insulated with fiberglass

QTR-1RC Reflectance Sensor (2-Pack)

The QTR-1RC reflectance sensor carries a single infrared LED and phototransistor pair in an inexpensive, tiny 0.5" x 0.3" module that can be mounted almost anywhere and is great for edge detection

Joystick Module for Arduino

Lots of robot projects need joystick. This module provides a affordable solution to that. Simply connect to two analog inputs, the robot is at your commands with X,Y control

HEADER, 0.5MM, 2.5MM HEIGHT, 20WAY

Manufacturer: KYOCERAManufacturer Part No: 14 5087 020 025 829+

TENMA - 72-7770 - MULTIMETER, DIGITAL, HAND HELD, 1999

DMM Functions: DC Current, Voltage, Resistance
Current Measure AC Max: -
Current Measure DC Max: 10A
Voltage Measure AC Max: 500V
Voltage Measure DC Max: 500V

Digital Blue LED Light Module

Introduction

This Blue LED light module has a shiny white color. It is ideal for Arduino starter. This module can be easy to be plugged on IO/Sensor expansion shield.

SOCKET IC, DIL, 0.3", 18WAY

The 1-390261-5 is a 18-way DIP Socket with 30% glass filled PBT, thermoplastic housing and tin-plated phosphor bronze contacts.

3334_0 - 57STH56 NEMA-23 Bipolar Stepper with 77:1 Gearbox

This powerful bipolar stepper with a rear shaft and a planetary gearbox has a 0.023° step angle and 240 kg·cm of torque at low speeds.

TB6612FNG Dual Motor Driver Carrier

This tiny board is an easy way to use Toshiba’s TB6612FNG dual motor driver, which can independently control two bidirectional DC motors or one bipolar stepper motor.

Arduino Mega ADK Rev3

The Arduino Mega ADK is a microcontroller board based on the ATmega2560. It has a USB host interface to connect with Android based phones.

3587_0 - CE-IB04-35A2-1.0/±50A DC Current Transducer

This bi-directional current transducer measures ±50 amps DC on a wire that passes through its window.

Polystyrene sheet - 300mm x 200mm x 3mm

Polystyrene is easy to work with.

You can drill or saw the material quite easily.

3523_0 - Lanbao CR18SCN08DNO Capacitive Proximity Sensor - 8mm

Product Features
This capacitive sensor can detect metals and some other materials within 8mm and behaves like a switch that connects to a digital input.

Product Description

This capacitive proximity sensor is used for non-contact detection of metallic and non-metallic objects such as liquid, powder and granular materials; it can also detect materials through glass or plastic walls.

You are here

Description