February 2016

Kondo KRG-3 Gyro Sensor

It backs up stable automatic actions by accurate and quick detection of the angle and speed
The angular speed detected is output directly with analog voltage. It deals with various usage
Super compact and light : 22.5×12.5×7.8 mm, 1.8g

Kondo KRG-4 Gyro Sensor

The KRG-4 gyro sensor detects angular velocity quickly and correctly, helping a stable autonomous function.

It is compatible with RCB-3 (KHR-1HV, 2HV and Manoi) and is also compatible with RCB-4 (KHR-3HV).

 

  • DMM Functions: Voltage, Capacitance, Frequency, Resistance
  • Current Measure AC Max: -
  • Current Measure DC Max: -
  • Voltage Measure AC Max: 300V
  • Voltage Measure DC Max: 300V
  • Resistance Measure Max: 40Mohm

 

  • DMM Functions: DC Current, Voltage, Resistance
  • Current Measure AC Max: -
  • Current Measure DC Max: 10A
  • Voltage Measure AC Max: 500V
  • Voltage Measure DC Max: 500V

NEMA 17 bracket

All measurements are in milimeters. The brackets are symetrical.

All edges and holes are cut to a 45° angle to provide a smooth edge

Bag of 10 M3*12mm screw

Bag of 10 M3*12mm screw

Bag of 4 Vinyl End Caps for MakerBeam

End caps for MakerBeam in black vinyl. We finally can give our beams little feet. We think it gives them a nice finish.

3824_0 - Acrylic Enclosure for the 1019

This clear acrylic enclosure protects your Phidget and is assembled with a Phillips screwdriver.

The 3824 Enclosure is designed to protect the Rev 1 version of the 1019 – PhidgetInterfaceKit 8/8/8 w/6 Port Hub while giving you access to all terminals and connectors through openings in the enclosure.

Triple Axis Accelerometer MMA7361

The MMA7361 from Freescale is a very nice sensor with easy analog interface. The MMA7361 is a 3.3V part and outputs an analog voltage for each of the three outputs. This voltage is in ratio to the measured acceleration and to the supply voltage (ratiometric). It has selectable sensitivity by dip switch.

If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The Lithium Battery Charger can charge 3.7V LiPo battery at a rate of 500mA per hour. It is designed to charge single-cell Li-Ion or Li-Polymer batteries. Check the datasheet below to see if it will work with your battery.

APM Power Module with XT60 Connectors

APM Power Module

The APM Power Module is a simple way of providing your APM with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable.

3DR Radio Cable for APM 1.X and APM 2.0

With this custom cable you can connect your XBee or 3DR Radio set up to the telemetry port on the "Oil Pan" IMU or APM 2.0 without having to use several jumper cables!

25 cm

Pololu Adjustable Step-Up/Step-Down Voltage Regulator S7V8A

The S7V8A switching step-up/step-down regulator efficiently produces an adjustable output between 2.5 V to 8 V from input voltages between 2.7 V and 11.8 V. Its ability to convert both higher and lower input voltages makes it useful for applications where the power supply voltage can vary greatly, as with batteries that start above but discharge below the regulated voltage.

The LV‑MaxSonar‑EZ0 has the widest and most sensitive beam pattern of any unit from LV‑MaxSonar‑EZ sensor line. This makes the LV‑MaxSonar‑EZ0 an excellent choice for use where high sensitivity, wide beam, or people detection is desired.

MB1020 LV-MaxSonar®-EZ2™

The LV-MaxSonar-EZ2 is a good compromise between sensitivity and side object rejection. The LV-MaxSonar-EZ2 is an excellent choice for applications that require slightly less side object detection and sensitivity than the MB1010 LV-MaxSonar-EZ1.

 

The Arduino OBD-II Kit consists of an OBD-II UART adapter which provides an OBD-II to UART data bridge, and a dedicated library for Arduino.

1032_0 - PhidgetLED-64 Advanced

This Phidget uses PWM to control the brightness of up to 64 LEDs.

The PhidgetLED 64 allows you to independently control 64 Light Emitting Diodes. Each LED can have the current limit set individually, and the brightness controlled from 0 to 100% within that limit using pulse-width modulation.

1067_0 - PhidgetStepper Bipolar HC
Accurately control one bipolar stepper motor with this controller. This board comes with a number of safety features.

The 1067 – PhidgetStepper Bipolar HC allows you to control the position, velocity, and acceleration of one bipolar stepper motor. This is the product you want to use to control larger industrial steppers or for applications that need a lot of torque.

1073_0 - PhidgetSBC3

Single board computer running Debian 7.0 with 128 MiB DDR2 SDRAM, 1 GiB Flash, integrated 1018 and 6 USB 2.0 High Speed 480Mbits/s ports.

3081_0 - Power Supply 12VDC 5.0A - EU

Removable European style wall plug.

The 3081 provides efficient power at 12DC, 5.0 Amps, 60 Watts. It is protected against over-current, over-voltage, short-circuits and over-temperature.

3555_0 - ASR2803-3-1M-BNC ORP Lab Electrode

This lab electrode measures the ORP of a solution and connects to the 1130 - pH/ORP Adapter.

1041_0 - PhidgetSpatial 0/0/3 Basic

This spatial board had a 3-axis, ±8g accelerometer and connects to your computer via USB.

3206_0 - SpringRC Micro Servo (SM-S2313M)

This tiny servo has 180° of travel and weighs 14g, making it ideal for applications where size and weight matter.

Flush cutting nippers TR 25

Tool for a flush cut. One of the most popular cutting tool. Safety clip for holding wire scraps securely after cutting available (order code TR 25 A). Safety clip type AF. Steel thickness 2.5mm. Tool length 138mm.
 

Chamfered cut nippers TTR 5500

Strong tool for a chamfered cut. Special TUNGSTEN treatment of blades. Ideal for the cutting of copper, ferrous materials and other hard components such as steel wire. Stronger that TTR5000.

Flush cutting nippers TR 30 15

Tool for a perfect clean and flush cut. It cuts the component lead at 1.5mm from the surface. Steel thickness 3.0mm. Tool length 138mm. ESD-safe handles version available .

Pages