December 2015

3823_1 - Acrylic Enclosure for the 3060

Product Features
This clear acrylic enclosure protects your Phidget and is assembled with a Phillips screwdriver.

Product Description

The 3823 Enclosure is designed to protect the Rev 0 version of the 3060 – USB Isolator while giving you access to all terminals and connectors through openings in the enclosure.

You can plug and unplug cables, connect and disconnect devices, without having to open the enclosure.

3900_0 - RFID Tag - PVC Key Fob White

Product Features
A white PVC key fob RFID tag. Uses EM4102 protocol.

Product Description

This durable plastic RFID tag can be used as a key fob or fastened onto any surface using it's finished through hole. The tag contains a unique ID that can be read by the 1024 at a distance of 7cm or less.

3959_0 - AC Solid State Relay - 280V 25A

Product Features
This SSR switches up to 280VAC / 25A and connects to any device with a digital output.

Product Description

For AC switching applications, this solid state relay is economical and reliable. Using the digital outputs from a Phidgets device, you can control the relay to silently switch a AC circuit at 280V/25A or less. There's an indicator LED on the control side of the circuit so you can tell the state of the relay at a glance.

10:1 Micro Metal Gearmotor

This gearmotor is a miniature (0.94" x 0.39" x 0.47"), high-quality, low-current motor with 10:1 metal gearbox, similar to Sanyo’s popular 12 mm gearmotors. These units have a 0.365"-long, 3 mm-diameter D-shaped output shaft.

Key specs at 6 V: 1300 RPM and 40 mA free-run, 2 oz-in (0.2 kg-cm) and 0.36 A stall.

10:1 Micro Metal Gearmotor HP

This gearmotor is a miniature (0.94" x 0.39" x 0.47"), high-power brushed DC motor with 10:1 metal gearbox, similar to Sanyo’s popular 12 mm gearmotors. These units have a 0.365"-long, 3 mm-diameter D-shaped output shaft.

Key specs at 6 V: 3000 RPM and 120 mA free-run, 4 oz-in (0.3 kg-cm) and 1.6 A stall.

100:1 Micro Metal Gearmotor

This gearmotor is a miniature (0.94" x 0.39" x 0.47"), low-current brushed DC motor with 100:1 metal gearbox, similar to Sanyo’s popular 12 mm gearmotors. These units have a 0.365"-long, 3 mm-diameter D-shaped output shaft.

Key specs at 6 V: 120 RPM and 40 mA free-run, 12 oz-in (0.9 kg-cm) and 0.36 A stall.

100:1 Micro Metal Gearmotor HP

This gearmotor is a miniature (0.94" x 0.39" x 0.47"), high-quality, high-power motor with 100:1 metal gearbox, similar to Sanyo’s popular 12 mm gearmotors. These units have a 0.365"-long, 3 mm-diameter D-shaped output shaft.

Key specs at 6 V: 320 RPM and 80 mA free-run, 30 oz-in (2.2 kg-cm) and 1.6 A stall.

16mm Speaker: 16 Ohm, 0.5 W

This small, 0.5 W speaker is a compact way to add high-fidelity sound (compared to typical units this size) that can bring your project to life. It includes two 30mm leads, and masked adhesive around the speaker face allows for easy mounting.

This small, 0.5 W speaker is compact way to add high-fidelity sound (compared to typical units this size) that can bring your project to life (or to annoy your friends and family with loud sirens and squawks!).

2-AAA Battery Holder

This battery holder features two 6", 24-gauge leads that have 5 mm of insulation stripped off of the ends.

2-AAA Battery Holder, Enclosed with Switch

Enclosed battery holder for two AAA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose them. It also features a switch that lets you open and close the electrical connection between the batteries and the holder’s leads.

30:1 Micro Metal Gearmotor HP

This gearmotor is a miniature (0.94" x 0.39" x 0.47"), high-quality, high-power motor with 30:1 metal gearbox, similar to Sanyo’s popular 12 mm gearmotors. These units have a 0.365"-long, 3 mm-diameter D-shaped output shaft.

Key specs at 6 V: 1000 RPM and 120 mA free-run, 9 oz-in (0.6 kg-cm) and 1.6 A stall.

378:1 Metal Gearmotor 25Dx58L mm

This cylindrical, 2.28" x 0.98" x 0.98" brushed DC gearmotor with a 378:1 metal gearbox is a lower-current , lower-speed alternative to our 25D mm HP gearmotors. These units have a 0.315"-long, 4 mm-diameter D-shaped output shaft.

Key specs at 6 V: 15 RPM and 80 mA free-run, 250 oz-in (18.0 kg-cm) and 2.2 A stall. (Note: stall torque and current specifications are theoretical values; stalling the motor is likely to damage the gearbox.)

3pi Expansion Kit without Cutouts - Black

This kit gives you everything you need to add a second level to your 3pi robot. In this version, the LCD pins are brought up to the expansion board from the base via extended headers for your own custom use. This black printed circuit board matches the color of the 3pi and can also serve as a general-purpose round prototyping board.

5:1 Micro Metal Gearmotor HP

This gearmotor is a miniature (0.94" x 0.39" x 0.47"), high-power brushed DC motor with 5:1 metal gearbox, similar to Sanyo’s popular 12 mm gearmotors. These units have a 0.365"-long, 3 mm-diameter D-shaped output shaft.

Key specs at 6 V: 6000 RPM and 120 mA free-run, 2 oz-in (0.1 kg-cm) and 1.6 A stall.

50:1 Micro Metal Gearmotor HP

This gearmotor is a miniature (0.94" x 0.39" x 0.47"), high-power brushed DC motor with 50:1 metal gearbox, similar to Sanyo’s popular 12 mm gearmotors. These units have a 0.365"-long, 3 mm-diameter D-shaped output shaft.

Key specs at 6 V: 625 RPM and 100 mA free-run, 15 oz-in (1.1 kg-cm) and 1.6 A stall.

A4988 Stepper Motor Driver Carrier

The A4988 stepper motor driver carrier is a breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver. The driver features adjustable current limiting, overcurrent and overtemperature protection, and five different microstep resolutions (down to 1/16-step).

It operates from 8 – 35 V and can deliver up to approximately 1 A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient additional cooling).

A4988 Stepper Motor Driver Carrier with Voltage Regulators

The A4988 stepper motor driver carrier with voltage regulators is a breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver. The board has two voltage regulators (5 V and 3.3 V), eliminating the need for separate logic and motor supplies.The driver features adjustable current limiting, overcurrent and overtemperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 – 35 V and can deliver up to approximately 1 A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient additional cooling).

ACS709 Current Sensor Carrier -75 to +75A

This board is a simple carrier of Allegro’s ±75A ACS709 Hall effect-based linear current sensor with overcurrent fault output, which offers a low-resistance (~1.1 mΩ) current path and electrical isolation up to 2.1 kV RMS. The sensor has optimized accuracy for currents from -37.5 A to 37.5 A, and the analog voltage output is linear for current magnitudes up to 75 A. The ratiometric output voltage is centered at VCC/2 and has a typical error of ±2%. It operates from 3 V to 5.5 V, so it can interface directly to both 3.3 V and 5 V systems

ACS714 Current Sensor Carrier -30 to +30A

This board is a simple carrier of Allegro’s ±30A ACS714 Hall effect-based linear current sensor, which offers a low-resistance (~1.2 mΩ) current path and electrical isolation up to 2.1 kV RMS. This version accepts a bidirectional current input with a magnitude up to 30 A and outputs a proportional analog voltage (66 mV/A) centered at 2.5 V with a typical error of ±1.5%. It operates from 4.5 V to 5.5 V and is intended for use in 5 V systems.

ACS714 Current Sensor Carrier -5A to +5A

This board is a simple carrier of Allegro’s ±5A ACS714 Hall effect-based linear current sensor, which offers a low-resistance (~1.2 mΩ) current path and electrical isolation up to 2.1 kV RMS. This version accepts a bidirectional current input with a magnitude up to 5 A and outputs a proportional analog voltage (185 mV/A) centered at 2.5 V with a typical error of ±1.5%. It operates from 4.5 V to 5.5 V and is intended for use in 5 V systems.

ACS715 Current Sensor Carrier 0 to 30A

This board is a simple carrier of Allegro’s 30A ACS715 Hall effect-based linear current sensor, which offers a low-resistance (~1.2 mΩ) current path and electrical isolation up to 2.1 kV RMS. This version accepts a unidirectional current input up to 30 A and outputs a proportional analog voltage (133 mV/A) that measures 500 mV when the input current is zero. The typical output error is ±1.5%. It operates from 4.5 V to 5.5 V and is intended for use in 5 V systems.

ARM mbed NXP LPC1768 Development Board

The mbed NXP LPC1768 is an easy-to-use MCU development board designed for rapid prototyping. At its heart is a powerful 32-bit ARM Cortex-M3 processor running at 96 MHz with 512 KB flash and 32 KB RAM, which makes it far more capable than popular 8-bit prototyping alternatives. A comprehensive firmware library and plenty of sample code help you get your program up and running quickly, and a free online IDE and C++ compiler means that no software installation is required. Downloading programs is as simple as using a USB flash drive (no external programmer is necessary).

Baby Orangutan B-328 Robot Controller

The Baby Orangutan B-328 is a very compact but complete robot controller, packing a high-performance ATmega328P AVR microcontroller (with 32 KB of program memory and 2 KB of RAM) and two motor drive channels in the same 24-pin form factor as competing units that include just a microcontroller. You can connect your battery, sensors, and motors directly to this small module to make a miniature robot, or you can use the Baby Orangutan as an auxiliary controller in larger robots.

0.100" (2.54 mm) Breakaway Male Header: 2x40-Pin, Straight

This connector is a double-row, 80-pin (2×40), straight male header strip that can be broken into smaller strips.

0.100" (2.54 mm) Breakaway Male Header: 1x40-Pin, Straight, Double-Sided

This connector is a single-row, 40-pin, straight male header strip that can be broken into smaller strips. Both sides of the strip are long, allowing for unique connections that cannot be made with standard male header strips. For example, this header can be used as a female-to-male adapter, and both sides are compatible with wire wrap.

0.100" (2.54 mm) Breakaway Male Header: 1x40-Pin, Straight

This connector is a single-row, 40-pin, straight male header strip that can be broken into smaller strips.

Crimping Tool: 0.08-0.5 mm² Capacity, 20-28 AWG

This crimping tool can be used to crimp both male and female versions of our JST connector crimp pins, JR crimp pins, Futaba J crimp pins, and crimp pins for 0.1" housings onto 20-28 AWG wires to make custom cables. The tool offers ratcheting action for increased consistency and ease of use.

BUY NOW

These female pins can be crimped on 22-28AWG wires and snapped into our crimp connector housings to create custom cables that are compatible with standard 0.1"-pitch headers and solderless breadboards. Our wires with pre-crimped terminals use these same pins. One female crimp pin pack consists of 100 pins.http://Female Crimp Pins for 0.1" Housings 100-Pac

0.100" (2.54 mm) Female Header: 1x10-Pin, Straight

This connector is a single-row, 10-pin, straight female header strip designed to match 0.1" male headers.

These 0.1" straight female header strips are commonly used as low-cost connectors for custom-made cables or perforated prototyping PCBs. The standard spacing is the same as on most solderless breadboards and matches 0.1" male header strips.

0.100" (2.54 mm) Female Header: 1x6-Pin, Straight

This connector is a single-row, 6-pin, straight female header strip designed to match 0.1" male headers.

These 0.1" straight female header strips are commonly used as low-cost connectors for custom-made cables or perforated prototyping PCBs. The standard spacing is the same as on most solderless breadboards and matches 0.1" male header strips.

Pages